Aaarrrgh
one probleme solved another came up.
The perimeter out was caused by the receiver wire to close to the mower motor. Rerouted it and the peri out is gone.
But
With imu activated the mower is now driving a curve instead a straight line
This is what i see on Strtup:
SETUP
--> ++++++++++++++++++++++++++++++++++* Start Robot Setup at 2502 --> +++++++++++++++++++++++++++
Load ErrorCounters
ErrorCounters address Start=500
ErrorCounters address Stop=522
UserSettings are read from EEprom Address : 2000 To 2501
Load Robot Stats
Robot Stats address Start = 800
Robot Stats address Stop = 826
IMU: found calib data
Load Calibration
Calibration address Start = 600
Calibration address Stop = 650
-------- IMU CALIBRATION --------
ACCEL GYRO MPU6050 OFFSET ax: 376 ay: -1768 az: 1512 gx: 91 gy: 12 gz: -2
COMPASS OFFSET X.Y.Z AND SCALE X.Y.Z --> comOfs=0.00,0.00,0.00
comScale=nan,nan,nan
.
--------------------------------------------------------------------------
--------------------------------- START IMU GYRO ACCEL -------------------
--------------------------------------------------------------------------
Connected with MPU-9250/MPU-9255
Wait for GYRO near 10 secondes
...........
Initial GYRO/ACCELL Yaw :-2.91 Pitch : 1.49 Roll : 0.24
With Offset GYRO/ACCELL Yaw :-2.91 Pitch : 0.00 Roll : 0.00
--------------------------------------------------------------------------
--------------------------------- START COMPASS --------------------------
--------------------------------------------------------------------------
Compass Yaw: 0.00 Diff between compass and accelGyro in Radian / Deg-0.05 / -2.91
--------------------------------------------------------------------------
--------------------------------- IMU READY ------------------------------
--------------------------------------------------------------------------
Change to Area : 1
New sigcode in use : 1,1,-1,-1,1,-1,1,-1,-1,1,-1,1,1,-1,-1,1,-1,-1,1,-1,-1,1,1,-1,
matchSignal size=24
subSample=4
capture size=192
------------------------------- GPS Initialisation --------------------------------------------
Send config sentence
End of Gps Config
START
Ardumower 1.42-Azuritber
Config: Ardumower
press...
d for menu
v to change console output (sensor counters, values, perimeter etc.)
off
Watchdog is enable and set to 2 secondes
one probleme solved another came up.
The perimeter out was caused by the receiver wire to close to the mower motor. Rerouted it and the peri out is gone.
But
With imu activated the mower is now driving a curve instead a straight line
This is what i see on Strtup:
SETUP
--> ++++++++++++++++++++++++++++++++++* Start Robot Setup at 2502 --> +++++++++++++++++++++++++++
Load ErrorCounters
ErrorCounters address Start=500
ErrorCounters address Stop=522
UserSettings are read from EEprom Address : 2000 To 2501
Load Robot Stats
Robot Stats address Start = 800
Robot Stats address Stop = 826
IMU: found calib data
Load Calibration
Calibration address Start = 600
Calibration address Stop = 650
-------- IMU CALIBRATION --------
ACCEL GYRO MPU6050 OFFSET ax: 376 ay: -1768 az: 1512 gx: 91 gy: 12 gz: -2
COMPASS OFFSET X.Y.Z AND SCALE X.Y.Z --> comOfs=0.00,0.00,0.00
comScale=nan,nan,nan
.
--------------------------------------------------------------------------
--------------------------------- START IMU GYRO ACCEL -------------------
--------------------------------------------------------------------------
Connected with MPU-9250/MPU-9255
Wait for GYRO near 10 secondes
...........
Initial GYRO/ACCELL Yaw :-2.91 Pitch : 1.49 Roll : 0.24
With Offset GYRO/ACCELL Yaw :-2.91 Pitch : 0.00 Roll : 0.00
--------------------------------------------------------------------------
--------------------------------- START COMPASS --------------------------
--------------------------------------------------------------------------
Compass Yaw: 0.00 Diff between compass and accelGyro in Radian / Deg-0.05 / -2.91
--------------------------------------------------------------------------
--------------------------------- IMU READY ------------------------------
--------------------------------------------------------------------------
Change to Area : 1
New sigcode in use : 1,1,-1,-1,1,-1,1,-1,-1,1,-1,1,1,-1,-1,1,-1,-1,1,-1,-1,1,1,-1,
matchSignal size=24
subSample=4
capture size=192
------------------------------- GPS Initialisation --------------------------------------------
Send config sentence
End of Gps Config
START
Ardumower 1.42-Azuritber
Config: Ardumower
press...
d for menu
v to change console output (sensor counters, values, perimeter etc.)
off
Watchdog is enable and set to 2 secondes